Tablet Mini Backpack

Tablet Pack

I was cycling on a bicycle trainer a little bit ago and I was trying to listen to some music on our stereo.  However, the trainer was too loud once I really started going.  So I switched to headphones and set my tablet down on a surface next to the trainer.  However, if I shifted around at all the head phones would pull out to one degree or another resulting in the music turning off.  I would then have to stop and reconnect the headphones and start peddling again.  A few minutes later I would move in a way that would disconnect my head phones again and I would have to fix things again. I repeated the process for almost forty minutes when I finally gave up on listening to music and just cycled to finish my workout.

This stopping and starting again prevented me from having a good workout and from letting my mind think about what going on in my life, like working out normally does. It was very dissatisfying.  So I tried to think of how I could have music to listen to without having such a disjointed workout.  I have a cycling jersey that has pockets in the back that I could put my tablet into; however my tablet is so sensitive that movement sometimes causes the music to pause as well.  Clearly I needed to shorten the distance that the cord to my headphones had to travel to my ears and a Bluetooth headset was out of our budget.  So how to fix the problem?

Then I thought, how close would it need to be to my ears to not get jostled.  I looked around at what other people had come up with as solutions for when they work out.  However, most people use their phones.  This was not an option for me.  However, if I could create something similar to what I have seen people make for their arms, for my back then maybe I could have the music I wanted.  So here is what I made.

Step #1

 

I found the right materials; focusing on finding something stretchy and that wouldn’t get waterlogged/sweat logged when I work out.  So I decided to use some of my toe socks (I love toe socks) that I had worn holes in and some stretch pants that my daughters have cut up.  I also found my notions. I knew I would need some elastic and Velcro.  So I pulled the elastic from some pj pants I had already cut up to make socks for my son. I then pulled the Velcro from a pair of cleats that were beyond use that I had saved the Velcro from months ago.

Step#2

 

I then traced around the edges of the tablet onto a piece of paper.  I then cut out this piece of paper and set it onto another piece of paper; where I added ¼ inch to each edge for seam allowance. Then cut out the pattern pieces that would be the front and back of the pack. Then I folded the pattern I had just created into a tri-fold like a letter. I traced the folded paper onto another sheet of paper that would be the pattern for the flap of the pack.  I then unfolded the paper and cut out the flap pattern I had created.

Step#3

 

I took my socks and cut off the toes (good bye cute toesL ).

Step #4

 

Then I took off the elastic at the top of the socks.

Step #5

 

Then I turned the socks so the holes in my socks were lined up as closely to a straight line as I could manage. Then I cut a straight line along the holes.  I then opened up the socks and laid them flat.

Step#6

Next I cut off the edges of the socks so that I now had an even rectangular shape.

Step#7

I laid the paper pattern on top of the sock material and pinned it down.

Step#8

I cut the sock material along the edges of the pattern. Then set the material aside.

Step#9

I took the stretch pants my daughters had cut and cut along the seams so that the pants then laid flat.

Step#10

I then pinned the pattern to the pants and cut out 2 pieces, one for the front and one for the back.

Step#11

I then took the elastics from the pj pants and seam ripped out the elastic from them.

Step#12

 

I then seam ripped the Velcro from the old leather flap from the cleat. Then I cleaned out all the old grass that had been caught in the Velcro.  Then I cut the Velcro into small rectangles for use to close the pack.

Step#13

I then stretched out the elastic across my back , starting on my back under my arm pit then going up and over my shoulder  to my collar bone. I then added about half an inch for seam allowance and cut the elastic.  Then I took the elastic I had cut and cut an identical piece for the other arm.

Step#14

I took the elastic and laid it out on a piece of paper and stretched it. Then marked then ends on the paper where it stretched to. Then I flipped the elastic over to the other side so that I would have a front and back measurement for the fabric that would go around the elastic. I did not add seam allowance here because I knew the pants would stretch around it and I wanted the material tight around it. I drew with a ruler the rectangle that I had marked edges for on the paper.  Then I cut of the pattern for the elastic cover.

Step#15

I laid the elastic pattern on top of the pants material and pinned it.

Step#16

I cut the elastic cover material out.

Step#17

I pinned the edges of the elastic cover material.

Step#18

I then stitched the elastic covers along the edge I had pinned.

Step#19

I took a safety pin and flipped them right side out.

Step#20

I then safety pinned the edge of the elastic and pulled the elastic into the inside of the tubes I had created for the elastic covers.

Step#21

I pinned the elastic to the edges of the elastic tubes to keep them in place.

Step#22

I then took the pattern paper for the tablet flap and laid it on the pants material.

Step#23

I pinned the pattern to the material.

Step#24

I cut 2 of the pants material flaps.

Step#25

I took the elastic from the top of my socks and cut them open.

Step#26

I pinned the two edges together.

Step#27

 

 

I hand stitched the two edges together. I chose to hand stitch the two edges because my machine tends to get stuck on small thick materials that need to be stitched together.

Step#28

 

I then took the two flap pieces and the elastic from the top of the sock and pinned them together.  I put the elastic inside the two flap pieces.

Step#29

I stitched the three pieces together. Starting along one of the short edges, turn, then along the edge that has the elastic in the middle, turn, then ending with the other short end of the flap.

Step#30

 

I then flipped it right side out.

Step#31

 

I then took the back outside material and laid the elastic down on top of it. Then I laid the flap on top of the elastic and pinned the three layers down. And I also pinned the elastic to the bottom edge.

Step#32

I then stitched along the three layers slowly so I didn’t break the needle in my machine.

Step#33

 

I then laid the back flap down and put the front flap on top of it. So the elastic and flap should be on the inside. Then pinned it along three edges, being sure to NOT pin the edge that has the flap on it.

Step #34

Again starting on the shorter edge I stitched down, turned and stitched along the longer edge, turned, then finished by stitching along the short end.

Step#35

I then flipped it out and it looked like this.

Step#36

I then set the pack aside for a minute and grabbed the sock rectangles.

Step#37

I pinned three edges.

Step#38

I stitched three edges, again starting on the short end, turn, stitch the long end, turn and stitch the other short end.

Step#39

I flipped the pink pack wrong sides out, and then tucked it inside the sock pocket I had sewn. Be sure that the sock pocket is wrong side out. The flap opening should be at the top.

Step#40

I then pinned the two edges together.

Step#41

I stitched along the edge but left a small opening so I could flip it right side out again.

Step#42

I flipped it right side out.

Step#43

I hand stitched the small opening closed with a hidden seam stitch.

Step#44

I then took the Velcro and pinned one side to the inside of the flap and then took the other side of the Velcro and pinned it to the front of the pack.

Step#45

I then stitched it down around the edge then made an x across the Velcro to further anchor it to the fabric.

I then slide it on and tried it out while cycling and it worked great. No cords came loose, or paused from my movement.  I have also used it when going around the house to clean or when I want to listen to a book. I have used it for about two months now and it has held up just fine. When it gets sweaty I just throw it in the wash. If you try to make this and you use a fabric that is not stretchy then I would suggest that you give more seam allowance and you will have to add more size for the height of your tablet. I did not add any size for this because my material was so stretchy and I wanted a tight fit, my end result was snug. I apologize for not having a picture of my tablet in the pack, I take my pictures with my tablet so I don't have one.

Materials                     Cost

Stretch pants-my daughter had cut    0.00

Toe socks- had holes in them         0.00

Elastic- taken from out grown pj’s     0.00

Velcro- taken from old unusable cleats 0.00

Threads- left over from other projects 0.00

Total Cost

                                  0.00